Skip to content
Exclusive official WM technics dealer for Spain, Portugal and Latin America
Very N'Ice
Very N'Ice technician with a WM Mammoth Lithium ice resurfacer

Guide · Blades

Ice resurfacer blades: how they work, when to sharpen them and when to replace them

The blade is the part that has the biggest effect on ice quality. Here is what it does, how to tell when it is worn and which blade each WM technics ice resurfacer uses.

What the blade of an ice resurfacer does

The blade sits under the machine, in the conditioner. It shaves a very thin layer off the ice surface and removes the marks and snow left by the skates. A screw conveyor collects that snow and carries it to the snow tank.

Behind the blade, the resurfacer spreads a thin layer of water that freezes and leaves the ice smooth. If the blade cuts well, the water spreads over a clean, even surface. If it cuts badly, the ice stays rough however much water goes down.

How to tell when the blade is worn

There is no fixed number of hours: it depends on how much the rink is used, how many resurfacing passes are made each day and how much dirt there is on the ice. These are the usual signs:

  • The ice shows grooves, lines or rough patches after the resurfacer has passed.
  • Loose snow is left on the rink, because the blade does not cut cleanly and the conveyor cannot pick it up.
  • You need more passes or more water to get the ice back to how it was.
  • The blade has nicks or dents, for example from a screw or a coin left on the ice.

A nicked blade leaves a mark along its whole path, so it is best to change it as soon as you notice.

Sharpening or replacing the blade

A blade is sharpened several times during its life, with a blade sharpener or at a sharpening workshop. When it is very worn or damaged, it is replaced with a new one.

The practical approach is to always keep a second sharp blade. When the fitted blade loses its edge, it is swapped in a few minutes and the rink does not stay closed while the other one is sharpened. That is why the WM Compact, WM Mammoth, WM Shira and WM Evo² come with two blades as standard.

Very N'Ice sells original WM technics replacement blades for every model to customers who bought their resurfacer from us. Sharpening is done by the rink itself or by a sharpening workshop.

New stainless steel blade for the WM Mammoth and WM Evo²

WM technics has launched a stainless steel resurfacing blade for the WM Mammoth and WM Evo². According to WM, it has been tested under real-world conditions and can last around four times longer than a conventional carbon steel blade. That means less frequent honing, less maintenance and more uptime for your ice resurfacer.

  • High-performance stainless steel with extreme hardness, excellent wear resistance and good corrosion resistance.
  • Up to four times the service life of a carbon steel blade.
  • Weighs about 3.5 kg: according to WM, the lightest resurfacing blade in the sector, so it is easier and safer to handle.
  • Changed in under a minute.
  • 2300 series available from mid-September 2026; 2100 series from mid-October 2026.

Very N'Ice sells it to customers who bought their WM Mammoth or WM Evo² from us. Ask us about it when you request a quote for your resurfacer.

Stainless steel blade brochure (PDF)

Changing the blade safely

Each model has its own procedure in the WM technics manual, but some rules always apply:

  • Wear protective gloves: the edge is extremely sharp.
  • Work with the machine switched off and the conditioner in the blade change position shown in the manual.
  • Keep the spare blade protected in its box so the edge does not get knocked.
  • After the change, adjust the blade as described in the manual for your model.

Which blade each WM resurfacer uses

MachineBlade widthBlade change and equipment
WM Pinguino1,400 mmTiltable conditioner for easy, safe blade changing
WM Compact1,700 mmTwo blades as standard
WM Mammoth2,100, 2,300 or 2,500 mmBlade change in under 60 seconds; super-light 3.5 kg blade; two blades in a transport box; available in stainless steel
WM Shira2,100 or 2,300 mmBlade change in about 5 minutes; market-standard thick blade; two blades
WM Evo²2,300 or 2,500 mmBlade change in under 60 seconds; super-light 3.5 kg blade; two blades in a transport box; available in stainless steel
WM Snip12 reversible 32 mm insertsEach insert has 2 cutting edges; the blade holder retains them on impact with metal or concrete

The wider the blade, the fewer passes it takes to cover the rink. The quick blade change on the Mammoth and Evo² keeps the time the rink is closed to a minimum.

Frequently asked questions

How often should an ice resurfacer blade be sharpened?

It depends on how the rink is used: skating hours, passes per day and dirt on the ice. The practical rule is to sharpen it when the ice starts to look rough or loose snow is left behind after the machine, and to always have a second sharp blade ready to swap in.

How long does it take to change the blade?

On the WM Mammoth and WM Evo², under 60 seconds thanks to their quick-change system. On the WM Shira, about 5 minutes.

Where can I buy replacement blades for a WM resurfacer?

Very N'Ice, the official WM technics dealer for Spain, Portugal and Latin America, sells original blades for every WM model to customers who bought their resurfacer from us.

Are there stainless steel blades for ice resurfacers?

Yes. WM technics makes a stainless steel blade for the WM Mammoth and WM Evo² which, according to WM, lasts up to four times longer than a carbon steel blade, weighs about 3.5 kg and is changed in under a minute. The 2300 series is available from mid-September 2026 and the 2100 series from mid-October 2026.

What blade width do I need?

The width depends on the machine: 1,400 mm on the WM Pinguino, 1,700 mm on the WM Compact and 2,100 to 2,500 mm on the WM Mammoth, WM Shira and WM Evo², depending on the version.

What is the WM Snip for if the resurfacer already cuts the edges?

All WM resurfacers except the WM Pinguino already have an edge cutter. But cutting the edges well along the boards depends on the operator's skill, and most find it hard to get the curved corners perfect. The WM Snip is a manually guided electric ice edger with 12 reversible inserts that goes over exactly those stretches. It is not always essential, but it is what it takes to leave the whole rink flawless.

Need blades for your WM resurfacer?

Send us the model and blade width. If you are looking for a new ice resurfacer, we will help you choose.